RGP30A, RGP30B, RGP30D, RGP30G, RGP30J, RGP30K
... Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vi ...
... Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vi ...
TECHNICAL SPECIFICATION FOR A 3 TO 15 KVA
... The static switch is composed of two pairs of SCRs, connected back-to-back. The switch can transfer the load from reserve to inverter or from inverter to reserve without losing power at the output. Therefore, it is a very important portion of a UPS. Detection circuitry is added to the control circui ...
... The static switch is composed of two pairs of SCRs, connected back-to-back. The switch can transfer the load from reserve to inverter or from inverter to reserve without losing power at the output. Therefore, it is a very important portion of a UPS. Detection circuitry is added to the control circui ...
ADS5411 数据资料 dataSheet 下载
... This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ...
... This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ...
810130 - BHD Rentals
... designed for the accurate measurement of capacitance and dissipation factor of electrical insulation. The bridge is suitable for making two-terminal, or threeterminal measurements on a specimen that may be grounded or floating. In the guarded, three-terminal, configuration the bridge is especially s ...
... designed for the accurate measurement of capacitance and dissipation factor of electrical insulation. The bridge is suitable for making two-terminal, or threeterminal measurements on a specimen that may be grounded or floating. In the guarded, three-terminal, configuration the bridge is especially s ...
air circuit breaker up to 6300a spec
... 2.6.1 A door interlock shall be provided so that it shall not be possible to open the door until the air circuit breaker moving part is in the disconnected position. 2.6.2 Insulated safety shutters shall be provided over the incoming and outgoing main circuits and over the auxiliary circuits. An int ...
... 2.6.1 A door interlock shall be provided so that it shall not be possible to open the door until the air circuit breaker moving part is in the disconnected position. 2.6.2 Insulated safety shutters shall be provided over the incoming and outgoing main circuits and over the auxiliary circuits. An int ...
Prevent Electrostatic Damage Booklet
... How Damage in Semiconductors Occurs and is Prevented An ESD event can occur when any charged conductor (including the human body) discharges to an ESDS (electrostatic discharge sensitive) device. The most common cause of electrostatic damage is the direct transfer of electrostatic charge from the hu ...
... How Damage in Semiconductors Occurs and is Prevented An ESD event can occur when any charged conductor (including the human body) discharges to an ESDS (electrostatic discharge sensitive) device. The most common cause of electrostatic damage is the direct transfer of electrostatic charge from the hu ...
FMMT489 Features Mechanical Data
... Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: ...
... Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: ...
INPUT and OUTPUT IMPEDANCE
... Establish the range of frequency at which the circuit works as an emitter follower. Find out what happens when the frequency is lowered. Check if there is distortion when too low frequencies are used. Repeat the procedure above by experimenting a smaller capacitance (10 nF). III.1B Input impedance o ...
... Establish the range of frequency at which the circuit works as an emitter follower. Find out what happens when the frequency is lowered. Check if there is distortion when too low frequencies are used. Repeat the procedure above by experimenting a smaller capacitance (10 nF). III.1B Input impedance o ...
MAX5440 Stereo Volume Control with Rotary Encoder Interface General Description
... The MAX5440 dual, 40kΩ logarithmic taper volume control features a debounced up/down interface for use with a simple rotary encoder without using a microcontroller (µC). Each potentiometer has 32 log-spaced tap points with a buffered wiper output and replaces mechanical potentiometers. An integrated ...
... The MAX5440 dual, 40kΩ logarithmic taper volume control features a debounced up/down interface for use with a simple rotary encoder without using a microcontroller (µC). Each potentiometer has 32 log-spaced tap points with a buffered wiper output and replaces mechanical potentiometers. An integrated ...
Operating instructions OT DMX...350/700 DIM SO
... The changes of current will not affect the color of the light, but only its intensity. The light intensity depends very much on the temperature of the LED. For example, if an LED driven at 700 mA reaches a high temperature, its light output may decline by half. So, if you lower the current passing t ...
... The changes of current will not affect the color of the light, but only its intensity. The light intensity depends very much on the temperature of the LED. For example, if an LED driven at 700 mA reaches a high temperature, its light output may decline by half. So, if you lower the current passing t ...
MAX7323 I C Port Expander with 4 Push-Pull Outputs and 4 Open-Drain I/Os
... Any of the four open-drain ports can be configured as a logic input by setting the port output logic-high (logichigh for an open-drain output is high impedance). When the MAX7323 is read through the serial interface, the actual logic levels at the ports are read back. The four ports offer latching t ...
... Any of the four open-drain ports can be configured as a logic input by setting the port output logic-high (logichigh for an open-drain output is high impedance). When the MAX7323 is read through the serial interface, the actual logic levels at the ports are read back. The four ports offer latching t ...
Interfacing to MM74HC High-Speed CMOS Logic Interfacing to
... valid CMOS logic “1” level. If the TTL circuit is only driving CMOS, its output voltage is usually about 3.5V. HC-CMOS typically recognizes levels greater than 3V as a logic high, so in most instances TTL can drive MM74HC. To see why TTL does not pull up further, Figure 1 shows a typical standard TT ...
... valid CMOS logic “1” level. If the TTL circuit is only driving CMOS, its output voltage is usually about 3.5V. HC-CMOS typically recognizes levels greater than 3V as a logic high, so in most instances TTL can drive MM74HC. To see why TTL does not pull up further, Figure 1 shows a typical standard TT ...
