MAX2900–MAX2904 200mW Single-Chip Transmitter ICs for 868MHz/915MHz ISM Bands General Description
... o Small 28-Pin QFN Package with Exposed Pad (5mm 5mm) ...
... o Small 28-Pin QFN Package with Exposed Pad (5mm 5mm) ...
SP481_83_85, Low Power Half-Duplex RS-485 Transceivers
... to be connected to a data bus, making it an ideal choice for multi-drop applications. Since the cabling can be as long as 4,000 feet, RS-485 transceivers are equipped with a wide (-7V to +12V) common mode range to accommodate ground potential differences. Because RS-485 is a differential interface, ...
... to be connected to a data bus, making it an ideal choice for multi-drop applications. Since the cabling can be as long as 4,000 feet, RS-485 transceivers are equipped with a wide (-7V to +12V) common mode range to accommodate ground potential differences. Because RS-485 is a differential interface, ...
RF2516 VHF/UHF TRANSMITTER Features
... keyless entry systems popular on many new cars and trucks, and the ubiquitous garage door opener. Other applications are emerging with the growth in home security, automation and the advent of various remote control applications. Typically these devices have been simplex, or one-way, links. They are ...
... keyless entry systems popular on many new cars and trucks, and the ubiquitous garage door opener. Other applications are emerging with the growth in home security, automation and the advent of various remote control applications. Typically these devices have been simplex, or one-way, links. They are ...
min i mum drop out volt age on a se rial pnp tran sis tor
... 500 Gy), and in the case of the experiment with low load current, degradation of the emitter injection efficiency of the elementary round lateral pnp transistors was not so important. The small perimeter-to-area ratio of the older technological process was, in this case, advantageous, having a small ...
... 500 Gy), and in the case of the experiment with low load current, degradation of the emitter injection efficiency of the elementary round lateral pnp transistors was not so important. The small perimeter-to-area ratio of the older technological process was, in this case, advantageous, having a small ...
LECTURE.2.Electricity
... Ion channels in membrane provide sites through which selective ions flow, thereby giving some TRANSMEMBRANE CONDUCTANCE Flow of ions in cytosol only limited by diameter of axon; the WIDER the axon, the greater the AXIAL CONDUCTANCE ...
... Ion channels in membrane provide sites through which selective ions flow, thereby giving some TRANSMEMBRANE CONDUCTANCE Flow of ions in cytosol only limited by diameter of axon; the WIDER the axon, the greater the AXIAL CONDUCTANCE ...
AD595 Datasheet - SparkFun Electronics
... accurately compensate for the reference junction over the rated operating range of the circuit, the AD594/AD595 is gain trimmed to match the transfer characteristic of J and K type thermocouples at 25°C. For a type J output in this temperature range the TC is 51.70 µV/°C, while for a type K it is 40 ...
... accurately compensate for the reference junction over the rated operating range of the circuit, the AD594/AD595 is gain trimmed to match the transfer characteristic of J and K type thermocouples at 25°C. For a type J output in this temperature range the TC is 51.70 µV/°C, while for a type K it is 40 ...
An electrical machine with integrated drive LCL filter components
... into electric machines can be achieved by sharing the existing machine’s magnetic circuit with the filter component. In this paper part of an LCL line filter has been chosen to be integrated with a permanent magnet synchronous machine. An LCL filter has been selected as it has lower inductance compa ...
... into electric machines can be achieved by sharing the existing machine’s magnetic circuit with the filter component. In this paper part of an LCL line filter has been chosen to be integrated with a permanent magnet synchronous machine. An LCL filter has been selected as it has lower inductance compa ...
LTC1069-6 - Single Supply, Very Low Power, Elliptic Lowpass Filter
... be the filter’s power supply. The analog ground of the filter should be connected to the clock’s ground at a single point only. Table 1 shows the clock’s low and high level threshold value for a dual or single supply operation. A pulse generator can be used as a clock source provided the high level ON ...
... be the filter’s power supply. The analog ground of the filter should be connected to the clock’s ground at a single point only. Table 1 shows the clock’s low and high level threshold value for a dual or single supply operation. A pulse generator can be used as a clock source provided the high level ON ...
Installation and Operating Instructions
... current. This is helpful for two reasons. Temporary dc lines are often used to connect to the dc bus, and large wire may not be available for quick installation in an emergency. Also the input feed may need to be connected to a source with limited current capability. Reducing the output current will ...
... current. This is helpful for two reasons. Temporary dc lines are often used to connect to the dc bus, and large wire may not be available for quick installation in an emergency. Also the input feed may need to be connected to a source with limited current capability. Reducing the output current will ...
4.0 - Electrical Principles
... • Power » Rate at which energy is transferred » Rate of doing work (using energy) over time » Unit for electrical power is the watt ...
... • Power » Rate at which energy is transferred » Rate of doing work (using energy) over time » Unit for electrical power is the watt ...
Chapter 3b : Power Analysis
... correct a load of 140 kVAR at 0.85 lagging pf to unity pf. Assume the load is supplied by a 110V (rms) 60Hz power line. ...
... correct a load of 140 kVAR at 0.85 lagging pf to unity pf. Assume the load is supplied by a 110V (rms) 60Hz power line. ...
HMC1097LP4E 数据资料DataSheet下载
... Quadrature Modulator RFIC which is ideal for digital modulation applications from 0.1 to 6.0 GHz including; Cellular/3G, WiMAX/4G, Broadband Wireless Access & ISM circuits. Housed in a compact 4x4 mm (LP4) SMT QFN package, the RFIC requires minimal external components & provides a low cost alternati ...
... Quadrature Modulator RFIC which is ideal for digital modulation applications from 0.1 to 6.0 GHz including; Cellular/3G, WiMAX/4G, Broadband Wireless Access & ISM circuits. Housed in a compact 4x4 mm (LP4) SMT QFN package, the RFIC requires minimal external components & provides a low cost alternati ...
DS1083L 16MHz to 134MHz Spread-Spectrum Clock Modulator for LCD Panels General Description
... dithers, the output clock about the center input frequency at a pin-selectable magnitude. The DS1083L automatically adjusts the dither rate based on the input clock frequency to maximize the EMI reduction. By dithering the system clock, all the address, data, and timing signals generated from this s ...
... dithers, the output clock about the center input frequency at a pin-selectable magnitude. The DS1083L automatically adjusts the dither rate based on the input clock frequency to maximize the EMI reduction. By dithering the system clock, all the address, data, and timing signals generated from this s ...
PAM2305 Description Pin Assignments
... This formula has a maximum at VIN = 2VOUT, where IRMS = IOUT /2. This simple worst-case condition is commonly used for design because even significant deviations do not offer much relief. Note that the capacitor manufacturer's ripple current ratings are often based on 2000 hours of life. This makes ...
... This formula has a maximum at VIN = 2VOUT, where IRMS = IOUT /2. This simple worst-case condition is commonly used for design because even significant deviations do not offer much relief. Note that the capacitor manufacturer's ripple current ratings are often based on 2000 hours of life. This makes ...
DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
... rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ...
... rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ...
A Successive Approximation Technique for Displaying Gray Shades
... stant (independent of the data) terms that are present in the addressing techniques of the RMS responding matrix LCDs. The RMS voltage across the pixels will correspond to gray-shade data if the pixels are selected with “ ” select voltages (corresponding to the “ ” bits) successively by applying the ...
... stant (independent of the data) terms that are present in the addressing techniques of the RMS responding matrix LCDs. The RMS voltage across the pixels will correspond to gray-shade data if the pixels are selected with “ ” select voltages (corresponding to the “ ” bits) successively by applying the ...
ADC128S102QML-SP Radiation Hardened 8
... The absolute maximum junction temperature (TJmax) for this device is 175°C. The maximum allowable power dissipation is dictated by TJmax, the junction-to-ambient thermal resistance (RθJA), and the ambient temperature (TA), and can be calculated using the formula PDMAX = (TJmax − TA)/RθJA. The values ...
... The absolute maximum junction temperature (TJmax) for this device is 175°C. The maximum allowable power dissipation is dictated by TJmax, the junction-to-ambient thermal resistance (RθJA), and the ambient temperature (TA), and can be calculated using the formula PDMAX = (TJmax − TA)/RθJA. The values ...
Radiation tolerance
... Small Power dissipation (no massive cooling in the inner region) Switch voltages of up to ~10V (7V required for clear) Rise/fall times of <10ns for a load of 20pF. Radiation tolerance to some 100krad Bump bonding pads Minimal number of IO signals (These must be routed along the narrow balcony) Progr ...
... Small Power dissipation (no massive cooling in the inner region) Switch voltages of up to ~10V (7V required for clear) Rise/fall times of <10ns for a load of 20pF. Radiation tolerance to some 100krad Bump bonding pads Minimal number of IO signals (These must be routed along the narrow balcony) Progr ...
MP4030: Application Note for a TRIAC
... the primary switch (MOSFET) turns on at a fixed frequency and turns off when the current reaches the desired level. When the MOSFET turns off, the energy stored in the inductor forces the secondary side diode to turn on, and the inductor current decreases linearly from the peak value to zero. When t ...
... the primary switch (MOSFET) turns on at a fixed frequency and turns off when the current reaches the desired level. When the MOSFET turns off, the energy stored in the inductor forces the secondary side diode to turn on, and the inductor current decreases linearly from the peak value to zero. When t ...
Power electronics
Power electronics is the application of solid-state electronics to the control and conversion of electric power. It also refers to a subject of research in electronic and electrical engineering which deals with the design, control, computation and integration of nonlinear, time-varying energy-processing electronic systems with fast dynamics.The first high power electronic devices were mercury-arc valves. In modern systems the conversion is performed with semiconductor switching devices such as diodes, thyristors and transistors, pioneered by R. D. Middlebrook and others beginning in the 1950s. In contrast to electronic systems concerned with transmission and processing of signals and data, in power electronics substantial amounts of electrical energy are processed. An AC/DC converter (rectifier) is the most typical power electronics device found in many consumer electronic devices, e.g. television sets, personal computers, battery chargers, etc. The power range is typically from tens of watts to several hundred watts. In industry a common application is the variable speed drive (VSD) that is used to control an induction motor. The power range of VSDs start from a few hundred watts and end at tens of megawatts.The power conversion systems can be classified according to the type of the input and output power AC to DC (rectifier) DC to AC (inverter) DC to DC (DC-to-DC converter) AC to AC (AC-to-AC converter)