CSE 245 Lecture Notes
... A network that has a cut-set composed only of inductors and/or current sources or a loop that contains only of capacitors and/or voltage sources is called a degenerate network Example: The following network is a degenerate network since C1, C2 and C5 form a degenerate capacitor loop ...
... A network that has a cut-set composed only of inductors and/or current sources or a loop that contains only of capacitors and/or voltage sources is called a degenerate network Example: The following network is a degenerate network since C1, C2 and C5 form a degenerate capacitor loop ...
3200 Series Temperature/ Process Controllers
... All rights are strictly reserved. No part of this document may be reproduced, modified, or transmitted in any form by any means, nor may it be stored in a retrieval system other than for the purpose to act as an aid in operating the equipment to which the document relates, without the prior written ...
... All rights are strictly reserved. No part of this document may be reproduced, modified, or transmitted in any form by any means, nor may it be stored in a retrieval system other than for the purpose to act as an aid in operating the equipment to which the document relates, without the prior written ...
Piezo-Chapter2.pdf
... damping composites to the center of a 29.8-cm square plate made of thin aluminum. The patch was made of PZT fibers embedded in resin. Using a derivative feedback controller, they obtained a 70% attenuation of vibration and sound pressure levels. Active control of sound radiating from a plate was al ...
... damping composites to the center of a 29.8-cm square plate made of thin aluminum. The patch was made of PZT fibers embedded in resin. Using a derivative feedback controller, they obtained a 70% attenuation of vibration and sound pressure levels. Active control of sound radiating from a plate was al ...
+3.3V, ±15kV ESD-Protected, Fail-Safe, Hot-Swap, RS-485/RS-422 Transceivers General Description Features
... The MAX3070E–MAX3079E 3.3V, ±15kV ESD-protected, RS-485/RS-422 transceivers feature one driver and one receiver. These devices include fail-safe circuitry, guaranteeing a logic-high receiver output when receiver inputs are open or shorted. The receiver outputs a logic high if all transmitters on a t ...
... The MAX3070E–MAX3079E 3.3V, ±15kV ESD-protected, RS-485/RS-422 transceivers feature one driver and one receiver. These devices include fail-safe circuitry, guaranteeing a logic-high receiver output when receiver inputs are open or shorted. The receiver outputs a logic high if all transmitters on a t ...
AD5301 数据手册DataSheet 下载
... Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. N ...
... Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. N ...
PIC MCU Comparator Tips n Tricks
... output which the microcontroller can capture. The circuit is designed with two feedback paths around a comparator. The first is a positive hysteresis feedback which sets a two level threshold, VHI and VLO, based on the state of the comparator output. The second feedback path is an RC time circuit. T ...
... output which the microcontroller can capture. The circuit is designed with two feedback paths around a comparator. The first is a positive hysteresis feedback which sets a two level threshold, VHI and VLO, based on the state of the comparator output. The second feedback path is an RC time circuit. T ...
2253i/2253iX Series User Manual
... and manufacture of precision, programmable power supplies for R&D, test and measurement, process control, power bus simulation and power conditioning applications across diverse industrial segments. From bench top supplies to rack-mounted industrial power subsystems, AMETEK Programmable Power is the ...
... and manufacture of precision, programmable power supplies for R&D, test and measurement, process control, power bus simulation and power conditioning applications across diverse industrial segments. From bench top supplies to rack-mounted industrial power subsystems, AMETEK Programmable Power is the ...
MAX1156/MAX1158/MAX1174 14-Bit, 135ksps, Single-Supply ADCs with Bipolar Analog Input Range General Description
... The MAX1156/MAX1158/MAX1174 have an input scaler, which allows conversion of true bipolar input voltages and input voltages greater than the power supply, while operating from a single +5V analog supply. The input scaler attenuates and shifts the analog input to match the input range of the internal ...
... The MAX1156/MAX1158/MAX1174 have an input scaler, which allows conversion of true bipolar input voltages and input voltages greater than the power supply, while operating from a single +5V analog supply. The input scaler attenuates and shifts the analog input to match the input range of the internal ...
Functional Specification - EDMS
... This system is based on a two modes detection system: Active (converter OFF) and Passive (converter ON). In Active mode, when converter is OFF-state only, the load is polarized in common mode to +10 V versus earth on its negative output connexion point. This allows to detect any earthing leakage fau ...
... This system is based on a two modes detection system: Active (converter OFF) and Passive (converter ON). In Active mode, when converter is OFF-state only, the load is polarized in common mode to +10 V versus earth on its negative output connexion point. This allows to detect any earthing leakage fau ...
transmission lines.
... transmission lines. The design involves conversion of lumped-elements into distributed elements if the initial design is in lumped-elements. Simulation is to be used to verify the amplitude and phase responses of the designs. The filters are designed by the insertion loss method. Microwave and RF De ...
... transmission lines. The design involves conversion of lumped-elements into distributed elements if the initial design is in lumped-elements. Simulation is to be used to verify the amplitude and phase responses of the designs. The filters are designed by the insertion loss method. Microwave and RF De ...
Resistors
... thermal energy. All resistors generate heat as a product of their function. A resistor is made of a material that has a specific amount of resistance to current flow. By selecting the correct amount of desired resistance in a circuit the installer can control the amount of output that passes through t ...
... thermal energy. All resistors generate heat as a product of their function. A resistor is made of a material that has a specific amount of resistance to current flow. By selecting the correct amount of desired resistance in a circuit the installer can control the amount of output that passes through t ...
Analog Front-End Design for ECG Systems
... high-value resistors or any other kind of isolation circuitry. The lead selection circuitry determines the various electrode combinations to be measured based on the Eindhoven triangle and Wilson central terminal (see Ref 1 for more information). The ECG electrodes are high-impedance signal sources; ...
... high-value resistors or any other kind of isolation circuitry. The lead selection circuitry determines the various electrode combinations to be measured based on the Eindhoven triangle and Wilson central terminal (see Ref 1 for more information). The ECG electrodes are high-impedance signal sources; ...
Flight Computer Carrier Board Capstone
... The fc-carrier is designed to address the needs for a smaller, robust, more compact but yet fully featured flight computer carrier board that will allow easy interfacing with all other Avionics nodes with maximum performance. ...
... The fc-carrier is designed to address the needs for a smaller, robust, more compact but yet fully featured flight computer carrier board that will allow easy interfacing with all other Avionics nodes with maximum performance. ...