ZODIAC DATA SYSTEMS
... frequency of all other modules must be one of the following: 4kHz x 20 (= 4kHz), 4kHz x 21 (= 8kHz), 4kHz x 22 (= 16kHz), 4kHz x 23 (= 32kHz), 4kHz x 24 (= 64kHz), and so on; or 4kHz x 2-1 (= 2kHz), 4kHz x 2-2 (= 1kHz), 4kHz x 2-3 (= 0.5kHz), 4kHz x 2-4 (= 0.25kHz), and so on. ...
... frequency of all other modules must be one of the following: 4kHz x 20 (= 4kHz), 4kHz x 21 (= 8kHz), 4kHz x 22 (= 16kHz), 4kHz x 23 (= 32kHz), 4kHz x 24 (= 64kHz), and so on; or 4kHz x 2-1 (= 2kHz), 4kHz x 2-2 (= 1kHz), 4kHz x 2-3 (= 0.5kHz), 4kHz x 2-4 (= 0.25kHz), and so on. ...
UniMasr.com_109
... Ideal amplifier’s output depends only on input voltage difference and not on source and load resistances. This can be achieved by using fully mismatched resistance condition (Rid >> RS or infinite Rid and Ro << RL or zero Ro ). vo Av ...
... Ideal amplifier’s output depends only on input voltage difference and not on source and load resistances. This can be achieved by using fully mismatched resistance condition (Rid >> RS or infinite Rid and Ro << RL or zero Ro ). vo Av ...
Tektronix/old
... number as the gain (e.g., if your station number is 6, design the circuit to have a gain of 9) ...
... number as the gain (e.g., if your station number is 6, design the circuit to have a gain of 9) ...
PowerPoint Presentation - More Microphone Design/Application
... Unbalanced Lines Two wires to carry audio signal. XLR: 2 is still +, but (-) pin connected to ground (along with 1). TS: tip-sleeve, tip (+), sleeve (ground) ...
... Unbalanced Lines Two wires to carry audio signal. XLR: 2 is still +, but (-) pin connected to ground (along with 1). TS: tip-sleeve, tip (+), sleeve (ground) ...
HotShot Power Supply Kit
... The power supply in this kit should only be used on the 18” HotShot blankets. This is a wire wound transformer that is really tough. Electronic ‘switching’ transformers are subject to damaging line voltage surges that a wire wound transformer simply ignores. Installers should note that this is a SAF ...
... The power supply in this kit should only be used on the 18” HotShot blankets. This is a wire wound transformer that is really tough. Electronic ‘switching’ transformers are subject to damaging line voltage surges that a wire wound transformer simply ignores. Installers should note that this is a SAF ...
Untitled - Carhifi
... more, and is thus more flexible. But that’s the point: the three-channel amp has the not-to-besniffed-at advantage of being designed specifically for one single application – to power a front system and one or more subwoofers. For this reason the subwoofer channel in the A5 is on the one hand also s ...
... more, and is thus more flexible. But that’s the point: the three-channel amp has the not-to-besniffed-at advantage of being designed specifically for one single application – to power a front system and one or more subwoofers. For this reason the subwoofer channel in the A5 is on the one hand also s ...
STK4182II AF Power Amplifier (Split Power Supply
... For measurement of the available time for load short-circuit and output noise voltage, use the specified transformer power supply shown right. The output noise voltage is represented by the peak value on rms scale (VTVM) of average value indicating type. For AC power supply, use an AC stabilized pow ...
... For measurement of the available time for load short-circuit and output noise voltage, use the specified transformer power supply shown right. The output noise voltage is represented by the peak value on rms scale (VTVM) of average value indicating type. For AC power supply, use an AC stabilized pow ...
Introduction to Filters
... function of frequency on a linear frequency scale to a high enough frequency to show the high end dropoff of the amplifier, both the areas of gain drop-off will be very small and not show much detail. These are the regions of primary interest. For this reason the frequency-response curve is plotted ...
... function of frequency on a linear frequency scale to a high enough frequency to show the high end dropoff of the amplifier, both the areas of gain drop-off will be very small and not show much detail. These are the regions of primary interest. For this reason the frequency-response curve is plotted ...
VersaSync Rugged Time and Frequency Reference
... Timing Interface Summary (Standard Configuration) ...
... Timing Interface Summary (Standard Configuration) ...
STK4142II AF Power Amplifier (Split Power Supply) (25W + 25W min
... For measurement of the available time for load short-circuit and output noise voltage, use the specified transformer power supply shown right. The output noise voltage is represented by the peak value on rms scale (VTVM) of average value indicating type. For AC power supply, use an AC stabilized pow ...
... For measurement of the available time for load short-circuit and output noise voltage, use the specified transformer power supply shown right. The output noise voltage is represented by the peak value on rms scale (VTVM) of average value indicating type. For AC power supply, use an AC stabilized pow ...
TRANSPAK T700-0001 ™ Loop Powered Isolator
... aluminum housing which is sealed for protection against corrosion, moisture, dust and electrical noise, such as radio frequency interference (RFI) and electromagnetic (EMI) interference. Topmounted barrier terminal strip connections are provided. Optional mounting solutions and enclosures are also a ...
... aluminum housing which is sealed for protection against corrosion, moisture, dust and electrical noise, such as radio frequency interference (RFI) and electromagnetic (EMI) interference. Topmounted barrier terminal strip connections are provided. Optional mounting solutions and enclosures are also a ...
TDA7295 - STMicroelectronics
... complexity due to the need for sophisticated protection circuits. To overcome these substantial drawbacks, the use of power MOS devices, which are immune from secondary breakdown is highly desirable. The device described has therefore been developed in a mixed bipolar-MOS high voltage technology cal ...
... complexity due to the need for sophisticated protection circuits. To overcome these substantial drawbacks, the use of power MOS devices, which are immune from secondary breakdown is highly desirable. The device described has therefore been developed in a mixed bipolar-MOS high voltage technology cal ...
