MT-101: Decoupling Techniques
... ferrite saturates it becomes nonlinear and loses its filtering properties. Note that some ferrites, even before full saturation occurs, can be nonlinear. Therefore, if a power stage is required to operate with a low distortion output, the ferrite should be checked in a prototype if it is operating n ...
... ferrite saturates it becomes nonlinear and loses its filtering properties. Note that some ferrites, even before full saturation occurs, can be nonlinear. Therefore, if a power stage is required to operate with a low distortion output, the ferrite should be checked in a prototype if it is operating n ...
Corel Ventura - LH0032.CHP
... Note 2. Specification is at 25oC junction temperature due to requirements of high-speed automatic testing. Actual values at operating temperature will exceed the value at TJ = 25oC. When supply voltages are ±15V, no-load operating junction temperature may rise 40-60oC above ambient, and more under l ...
... Note 2. Specification is at 25oC junction temperature due to requirements of high-speed automatic testing. Actual values at operating temperature will exceed the value at TJ = 25oC. When supply voltages are ±15V, no-load operating junction temperature may rise 40-60oC above ambient, and more under l ...
Underwater Speakers
... This is, by far, the most important aspect of protecting the underwater speaker. Since the power to the speaker is not guaranteed by volume alone, the only safe method of ensuring a connection is to power the underwater speakers from a unique 30W maximum amplifier. The most common error of new sound ...
... This is, by far, the most important aspect of protecting the underwater speaker. Since the power to the speaker is not guaranteed by volume alone, the only safe method of ensuring a connection is to power the underwater speakers from a unique 30W maximum amplifier. The most common error of new sound ...
Chapter 21: Alternating Currents
... This circuit will allow low frequency signals to pass through while filtering out high frequency signals. ...
... This circuit will allow low frequency signals to pass through while filtering out high frequency signals. ...
HAWKEYE 720 Installation Instructions
... Installation Instructions INSTALLATION !CAUTION ! • This product is not intended for life or safety applications • Installing sensors in an energized motor control center or on any energized conductor can be hazardous. Severe injury or death can result from electrical shock during contact with high ...
... Installation Instructions INSTALLATION !CAUTION ! • This product is not intended for life or safety applications • Installing sensors in an energized motor control center or on any energized conductor can be hazardous. Severe injury or death can result from electrical shock during contact with high ...
13710237524571_01-Feedback Amplifiers
... larger compared with the source is represented by a Thevenin’s equivalent in its input circuit and a resistance Rs (Ri>> Rs), then Vi Vs. Norton’s equivalent in its output circuit. If the external load resistance RL is smaller compared with the output resistance Ro of the amplifier (Ro>> RL), then ...
... larger compared with the source is represented by a Thevenin’s equivalent in its input circuit and a resistance Rs (Ri>> Rs), then Vi Vs. Norton’s equivalent in its output circuit. If the external load resistance RL is smaller compared with the output resistance Ro of the amplifier (Ro>> RL), then ...
ZXLD1615 ADJUSTABLE DC-DC BOOST CONVERTER WITH INTERNAL SWITCH IN TSOT23-5 DESCRIPTION
... Suitable coils for use with the ZXLD1615 are shown in the table below: ...
... Suitable coils for use with the ZXLD1615 are shown in the table below: ...
NBB-400 CASCADABLE BROADBAND GaAs MMIC AMPLIFIER DC TO 8GHz Features
... • Die should be mounted to a clean, flat surface. Epoxy or eutectic die attach are both acceptable attachment methods. Top and bottom metallization are gold. Conductive silver-filled epoxies are recommended. This procedure involves the use of epoxy to form a joint between the backside gold of the ch ...
... • Die should be mounted to a clean, flat surface. Epoxy or eutectic die attach are both acceptable attachment methods. Top and bottom metallization are gold. Conductive silver-filled epoxies are recommended. This procedure involves the use of epoxy to form a joint between the backside gold of the ch ...
NEW: Read important application notes on page 4 ff.
... Some amplifiers only have a fixed bias voltage or the bias cannot be trimmed to near zero. In this case it is required to draw the ground level (which is not available on the input jack) from other sources, e.g. the output jack, special connectors or even from the housing. Please refer to the amplif ...
... Some amplifiers only have a fixed bias voltage or the bias cannot be trimmed to near zero. In this case it is required to draw the ground level (which is not available on the input jack) from other sources, e.g. the output jack, special connectors or even from the housing. Please refer to the amplif ...
Video Transcript - Rose
... The magnitude of the phase voltage of an ideal balanced three-phase Y-connected source is 400 V. The source is connected to a balanced Y-connected load through a transmission line that has an impedance of 1+j5 Ω. The load is a 19 Ω resistor in series with an inductive reactance and the magnitude of ...
... The magnitude of the phase voltage of an ideal balanced three-phase Y-connected source is 400 V. The source is connected to a balanced Y-connected load through a transmission line that has an impedance of 1+j5 Ω. The load is a 19 Ω resistor in series with an inductive reactance and the magnitude of ...
Development of Sensor Board for 802.11 DPAC
... +12V charge controller. It derives its 5V and 3.3V supplies using onboard regulators The 5 V power supply is based on an LM2673S-5.0 switching regulator. The 3.3 V power supply is derived from the 5 V supply using a Series LDO (LP3962ES-3.3) regulator. These two power supplies are used for D ...
... +12V charge controller. It derives its 5V and 3.3V supplies using onboard regulators The 5 V power supply is based on an LM2673S-5.0 switching regulator. The 3.3 V power supply is derived from the 5 V supply using a Series LDO (LP3962ES-3.3) regulator. These two power supplies are used for D ...
Resistors in Microwave Applications
... Nowadays frequencies up to 2 GHz are nothing special. Mobile phones operate in the 900 MHz frequency range (GSM) and 1,8 GHz (DCS) respectively. The DECT-standard will become more and more important, it is based upon 1,8 GHz too. By using this standard the telecom providers do not need to install an ...
... Nowadays frequencies up to 2 GHz are nothing special. Mobile phones operate in the 900 MHz frequency range (GSM) and 1,8 GHz (DCS) respectively. The DECT-standard will become more and more important, it is based upon 1,8 GHz too. By using this standard the telecom providers do not need to install an ...
A Universal and Optimized Embedded System to
... As ADC of ATmega32 is of 10-bit resolution hence the maximum value from the ADC with +5 volts reference will be 1023. Therefore, a scaling down factor of 5.66 is used. Eq. (2) gives 180.74 when potentiometer is fully rotated in clockwise direction (subjected to the position of potentiometer with res ...
... As ADC of ATmega32 is of 10-bit resolution hence the maximum value from the ADC with +5 volts reference will be 1023. Therefore, a scaling down factor of 5.66 is used. Eq. (2) gives 180.74 when potentiometer is fully rotated in clockwise direction (subjected to the position of potentiometer with res ...