RF5725 2.4GHz TO 2.5GHz SINGLE-BAND FRONT END MODULE Features
... The RF5725 FEM is a single-chip integrated front-end module (FEM) for high performance WiFi applications in the 2.4GHz to 2.5GHz ISM band. The FEM greatly reduces the number of external components minimizing footprint and assembly cost of the overall 802.11b/g solution. The RF5725 has an integrated ...
... The RF5725 FEM is a single-chip integrated front-end module (FEM) for high performance WiFi applications in the 2.4GHz to 2.5GHz ISM band. The FEM greatly reduces the number of external components minimizing footprint and assembly cost of the overall 802.11b/g solution. The RF5725 has an integrated ...
302 Compact Production Mixer
... In the field I had a chance to field test the 302 mixer on a long shoot in the arctic this fall. It was a joy to work with and came in very handy. We did one setup that involved recording the intercom in a small research aircraft. The only problem was that there was no room for a camera or sound per ...
... In the field I had a chance to field test the 302 mixer on a long shoot in the arctic this fall. It was a joy to work with and came in very handy. We did one setup that involved recording the intercom in a small research aircraft. The only problem was that there was no room for a camera or sound per ...
Clockless Chips - 123SeminarsOnly.com
... •High power dissipation:-Clock is a tiny crystal oscillator that keeps vibrating during all time as long as the system is power on, this lead into high power dissipation by the synchronous circuit. •High electro-magnetic noise:-It is associated with electromagnetic waves that produce electromagnetic ...
... •High power dissipation:-Clock is a tiny crystal oscillator that keeps vibrating during all time as long as the system is power on, this lead into high power dissipation by the synchronous circuit. •High electro-magnetic noise:-It is associated with electromagnetic waves that produce electromagnetic ...
ElectronicsPrimer
... Once a sampling rate has been determined the input must be bandlimited. This means that the incoming electrical signal is filtered so that all frequency components above one-half the sampling frequency are removed! Filtering not only prevents aliasing but also can be used to remove unwanted noise. ...
... Once a sampling rate has been determined the input must be bandlimited. This means that the incoming electrical signal is filtered so that all frequency components above one-half the sampling frequency are removed! Filtering not only prevents aliasing but also can be used to remove unwanted noise. ...
![INS0850 REV [Converted]](http://s1.studyres.com/store/data/007794622_2-8b0123f2c490c4c84e9afbca4e749f40-300x300.png)
INS0850 REV [Converted]
... line-level RCA signal path between the subwoofer and the main audio/video system. The unit provides 2 AC outlets and 2 signal-line protection circuits. It features Panamax’s exclusive Protect or Disconnect™ circuitry for AC surge protection, which, in order to keep your equipment safe, will disconne ...
... line-level RCA signal path between the subwoofer and the main audio/video system. The unit provides 2 AC outlets and 2 signal-line protection circuits. It features Panamax’s exclusive Protect or Disconnect™ circuitry for AC surge protection, which, in order to keep your equipment safe, will disconne ...
OP97
... differential voltage by back-to-back diodes. Current-limiting resistors are not used to maintain low noise performance. If differential voltages above ±1 V are expected at the inputs, series resistors must be used to limit the current flow to a maximum of 10 mA. Common-mode voltages at the inputs ar ...
... differential voltage by back-to-back diodes. Current-limiting resistors are not used to maintain low noise performance. If differential voltages above ±1 V are expected at the inputs, series resistors must be used to limit the current flow to a maximum of 10 mA. Common-mode voltages at the inputs ar ...
Diodes
... Build the circuit above. Use an 9-VRMS, 60-Hz supply. (a) Begin with the capacitor disconnected. Observe the full-wave rectified pattern on the oscilloscope. Verify that the frequency of the pattern is 120 Hz. [Note: Because the two channels of your oscilloscope have a common ground, it is not possi ...
... Build the circuit above. Use an 9-VRMS, 60-Hz supply. (a) Begin with the capacitor disconnected. Observe the full-wave rectified pattern on the oscilloscope. Verify that the frequency of the pattern is 120 Hz. [Note: Because the two channels of your oscilloscope have a common ground, it is not possi ...
MAX4364/MAX4365 1.4W and 1W, Ultra
... The MAX4364/MAX4365 are bridged audio power amplifiers intended for portable audio devices with internal speakers. The MAX4364 is capable of delivering 1.4W from a single 5V supply and 500mW from a single 3V supply into an 8Ω load. The MAX4365 is capable of delivering 1W from a single 5V supply and ...
... The MAX4364/MAX4365 are bridged audio power amplifiers intended for portable audio devices with internal speakers. The MAX4364 is capable of delivering 1.4W from a single 5V supply and 500mW from a single 3V supply into an 8Ω load. The MAX4365 is capable of delivering 1W from a single 5V supply and ...
PT4110
... The LED current is controlled by the feedback resistor. The feedback reference is 300mV. The LED current is 300mV/RFB. In order to have accuracy LED current, precision resistor is preferred. (1% is recommended). Selecting the inductor Choose an inductor that does not saturate under the worst-case lo ...
... The LED current is controlled by the feedback resistor. The feedback reference is 300mV. The LED current is 300mV/RFB. In order to have accuracy LED current, precision resistor is preferred. (1% is recommended). Selecting the inductor Choose an inductor that does not saturate under the worst-case lo ...
Discussion Question 11B
... If the AC generator weren’t present, our circuit would be a plain old undriven LC circuit with some resistance R thrown in. It would support a nice oscillating current of frequency ω0 = 1/√LC… except the resistor would damp out the oscillations over time. To keep the circuit going, we attach the gen ...
... If the AC generator weren’t present, our circuit would be a plain old undriven LC circuit with some resistance R thrown in. It would support a nice oscillating current of frequency ω0 = 1/√LC… except the resistor would damp out the oscillations over time. To keep the circuit going, we attach the gen ...
AD807 数据手册DataSheet 下载
... modulation in order to accurately retime jittered data. In order for the VCO output to have a phase modulation that tracks the input jitter, some modulation signal must be generated at the output of the phase detector. The modulation output from the phase detector can only be produced by a phase err ...
... modulation in order to accurately retime jittered data. In order for the VCO output to have a phase modulation that tracks the input jitter, some modulation signal must be generated at the output of the phase detector. The modulation output from the phase detector can only be produced by a phase err ...
