ZR4040-4.1 Description Pin Assignments
... The ZR4040-4.1 design provides a stable voltage without an external capacitor and is stable with capacitive loads. The ZR4040-4.1 is recommended for operation between 60μA and 15mA and so is ideally suited to low power and battery powered applications. ...
... The ZR4040-4.1 design provides a stable voltage without an external capacitor and is stable with capacitive loads. The ZR4040-4.1 is recommended for operation between 60μA and 15mA and so is ideally suited to low power and battery powered applications. ...
LTM4608A - Low VIN, 8A DC/DC uModule with Tracking, Margining, and Frequency Synchronization
... with 50k resistors from VIN to ground. See the Applications Information section and Figure 20. BSEL (B7): Margining Bit Select Pin. Tying BSEL low selects ±5%, tying it high selects ±10%. Floating it or tying it to VIN/2 selects ±15%. TRACK (E5): Output Voltage Tracking Pin. Voltage tracking is enab ...
... with 50k resistors from VIN to ground. See the Applications Information section and Figure 20. BSEL (B7): Margining Bit Select Pin. Tying BSEL low selects ±5%, tying it high selects ±10%. Floating it or tying it to VIN/2 selects ±15%. TRACK (E5): Output Voltage Tracking Pin. Voltage tracking is enab ...
RSAW_v1.0-VAR-002-AB-1.1b Reliability Standard Audit Worksheet Generator Operation for Maintaining Network Voltages
... equal to or greater than the generating unit terminal voltage must provide the ISO any one (1) or more of the following within thirty (30) days of a request: R7.1 tap settings; R7.2 available fixed tap ranges; R7.3 impedance data; and R7.4 the plus/minus voltage range with step-change in percentage ...
... equal to or greater than the generating unit terminal voltage must provide the ISO any one (1) or more of the following within thirty (30) days of a request: R7.1 tap settings; R7.2 available fixed tap ranges; R7.3 impedance data; and R7.4 the plus/minus voltage range with step-change in percentage ...
ADP3623 数据手册DataSheet 下载
... The signals applied to the inputs (INA, INA, INB, and INB) should have steep and clean fronts. It is not recommended to apply slow changing signals to drive these inputs because they can result in multiple switching when the thresholds are crossed, causing damage to the power MOSFET or IGBT. ...
... The signals applied to the inputs (INA, INA, INB, and INB) should have steep and clean fronts. It is not recommended to apply slow changing signals to drive these inputs because they can result in multiple switching when the thresholds are crossed, causing damage to the power MOSFET or IGBT. ...
PDF
... motor horsepower exceeds approximately 30% of the supply transformer(s) base kVA rating, if no generators are present [2]. Whereas, If generator is present, and no other sources are involved, an analysis should be done whenever the motor horsepower exceeds 10–15% of the generator kVA rating, dependi ...
... motor horsepower exceeds approximately 30% of the supply transformer(s) base kVA rating, if no generators are present [2]. Whereas, If generator is present, and no other sources are involved, an analysis should be done whenever the motor horsepower exceeds 10–15% of the generator kVA rating, dependi ...
High Voltage Ceramic Capacitors
... Typical Characteristics Data / Specifications and Test Methods ...
... Typical Characteristics Data / Specifications and Test Methods ...
SP211EH 数据资料DataSheet下载
... The SP211EH/213EH devices are high speed enhanced multi-channel RS-232 line transceivers with improved electrical performance. The SP211EH/213EH series is a superior drop-in replacement to our previous versions as well as popular industry standards. All devices feature very low power CMOS constructi ...
... The SP211EH/213EH devices are high speed enhanced multi-channel RS-232 line transceivers with improved electrical performance. The SP211EH/213EH series is a superior drop-in replacement to our previous versions as well as popular industry standards. All devices feature very low power CMOS constructi ...
Microwave Oven Technical File
... begins to melt naturally. Only when some water has formed, will the microwave energy start having an effect and the defrosting cycle begins. The delay caused is likely to result in the food not being completely defrosted when the defrosting cycle ends. The way to overcome this is to remove the food ...
... begins to melt naturally. Only when some water has formed, will the microwave energy start having an effect and the defrosting cycle begins. The delay caused is likely to result in the food not being completely defrosted when the defrosting cycle ends. The way to overcome this is to remove the food ...
DRTR5V0U4S Features Mechanical Data
... written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instruct ...
... written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instruct ...
V / VP / W 1
... The current/voltage characteristic of a filament lamp is to be determined using a datalogger, the data then being fed into a computer to give a visual display of the characteristic. Draw the circuit diagram required for such an experiment and state what is varied so as to produce a range of values. ...
... The current/voltage characteristic of a filament lamp is to be determined using a datalogger, the data then being fed into a computer to give a visual display of the characteristic. Draw the circuit diagram required for such an experiment and state what is varied so as to produce a range of values. ...
PAM8610 Description Pin Assignments
... The FADE terminal is a logic input that controls the operation of the volume control circuitry during transitions to and from the shutdown state and during power-up. A logic low on this terminal will set the amplifier in fade mode. During power-up or recovery from the shutdown state (a logic high is ...
... The FADE terminal is a logic input that controls the operation of the volume control circuitry during transitions to and from the shutdown state and during power-up. A logic low on this terminal will set the amplifier in fade mode. During power-up or recovery from the shutdown state (a logic high is ...
Current source
A current source is an electronic circuit that delivers or absorbs an electric current which is independent of the voltage across it.A current source is the dual of a voltage source. The term constant-current 'sink' is sometimes used for sources fed from a negative voltage supply. Figure 1 shows the schematic symbol for an ideal current source, driving a resistor load. There are two types - an independent current source (or sink) delivers a constant current. A dependent current source delivers a current which is proportional to some other voltage or current in the circuit.