BAT42WS / BAT43WS Features Mechanical Data
... written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instruct ...
... written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instruct ...
2924 Federal Register
... Nuclear One (ANO) that led to the NRC staff’s position requiring degraded voltage protection for nuclear power plant Class 1E (or safety related) electrical safety buses and expectations for voltage calculations for the plant offsite/onsite electric power system interface, are discussed below as a r ...
... Nuclear One (ANO) that led to the NRC staff’s position requiring degraded voltage protection for nuclear power plant Class 1E (or safety related) electrical safety buses and expectations for voltage calculations for the plant offsite/onsite electric power system interface, are discussed below as a r ...
MMBD4148SE Datasheet
... arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance w ...
... arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance w ...
Bates
... resistance much greater than the resistance across which the voltage is measured. The loading effect of a voltmeter causes too low a voltage reading because RV is too low as a parallel resistance. The digital multimeter (DMM) has practically no loading effect as a voltmeter because its input is ...
... resistance much greater than the resistance across which the voltage is measured. The loading effect of a voltmeter causes too low a voltage reading because RV is too low as a parallel resistance. The digital multimeter (DMM) has practically no loading effect as a voltmeter because its input is ...
AN11045 Next generation of NXP low VCEsat transistors
... overall collector-emitter resistance which can be achieved for the final component. The BISS-4 product portfolio has two branches. The first focuses on an ultra low VCEsat performance in order to minimize the saturation resistance as much as possible. The target for the development was to reach an R ...
... overall collector-emitter resistance which can be achieved for the final component. The BISS-4 product portfolio has two branches. The first focuses on an ultra low VCEsat performance in order to minimize the saturation resistance as much as possible. The target for the development was to reach an R ...
STM6710
... Factory-trimmed reset threshold options for monitoring 5.0 V, 3.3 V, 2.5 V and 1.8 V supplies with –5% and –10% tolerances are available. If a monitored supply voltage input falls below the minimum voltage threshold, a single active low output is asserted, triggering a system reset. This device can ...
... Factory-trimmed reset threshold options for monitoring 5.0 V, 3.3 V, 2.5 V and 1.8 V supplies with –5% and –10% tolerances are available. If a monitored supply voltage input falls below the minimum voltage threshold, a single active low output is asserted, triggering a system reset. This device can ...
Voltage Quality in the context of EMC
... by the grid operator or network owner. change when a certain load instantaneously is connected or disconnected, such as a maximum voltage step of 3 % for C. Examples of Electromagnetic Disturbances with Impact on connection or disconnection of the full contracted power Voltage Quality demand [15]. A ...
... by the grid operator or network owner. change when a certain load instantaneously is connected or disconnected, such as a maximum voltage step of 3 % for C. Examples of Electromagnetic Disturbances with Impact on connection or disconnection of the full contracted power Voltage Quality demand [15]. A ...
A Low-Power Wide-Linear-Range Transconductance Amplifier
... Abstract. The linear range of approximately ±75 mV of traditional subthreshold transconductance amplifiers is too small for certain applications—for example, for filters in electronic cochleas, where it is desirable to handle loud sounds without distortion and to have a large dynamic range. We descr ...
... Abstract. The linear range of approximately ±75 mV of traditional subthreshold transconductance amplifiers is too small for certain applications—for example, for filters in electronic cochleas, where it is desirable to handle loud sounds without distortion and to have a large dynamic range. We descr ...
580393681ADM3202_22_1385_c.pdf
... data transmission at rates well in excess of the EIA/RS-232E specifications. RS-232 voltage levels are maintained at data rates up to 460 kbps even under worst-case loading conditions. This allows high speed data links between two terminals and is suitable for the new generation ISDN modem standards ...
... data transmission at rates well in excess of the EIA/RS-232E specifications. RS-232 voltage levels are maintained at data rates up to 460 kbps even under worst-case loading conditions. This allows high speed data links between two terminals and is suitable for the new generation ISDN modem standards ...
PowerLogic® ION6200 Factory Assembled
... and 4 Analog Outputs wired to terminal blocks. One 10 Base-T Ethernet and 10 Base-FL equipped meter. Cate 5E and fiber cables will terminate directly on meter. Each RS-485 port will be daisy chained together and wired to terminal blocks. Tailored to any meter system voltage type: ...
... and 4 Analog Outputs wired to terminal blocks. One 10 Base-T Ethernet and 10 Base-FL equipped meter. Cate 5E and fiber cables will terminate directly on meter. Each RS-485 port will be daisy chained together and wired to terminal blocks. Tailored to any meter system voltage type: ...
Extending the MFJ-927 to 160-Meters
... In the “Reviews” section of this website I reviewed the CG-3000, MFJ-927, and the SG230 auto-tuners specifically for use with the popular 43-foot vertical antenna. As discussed in that review only the SG-230 had enough internal inductance to tune the 43foot vertical on 160 meters, so I described an ...
... In the “Reviews” section of this website I reviewed the CG-3000, MFJ-927, and the SG230 auto-tuners specifically for use with the popular 43-foot vertical antenna. As discussed in that review only the SG-230 had enough internal inductance to tune the 43foot vertical on 160 meters, so I described an ...
Transparent Current Mirrors Using a-GIZO TFTs: Simulation
... technology are fabrication at room-temperature [4], [5], better optical transparency and the relatively high mobility. These a-GIZO TFT applications are not only confined to displays (AMOLED) [6], but also extended to sensors [7]. The a-GIZO TFT technology is more recent among others. Hence the circ ...
... technology are fabrication at room-temperature [4], [5], better optical transparency and the relatively high mobility. These a-GIZO TFT applications are not only confined to displays (AMOLED) [6], but also extended to sensors [7]. The a-GIZO TFT technology is more recent among others. Hence the circ ...
Current source
A current source is an electronic circuit that delivers or absorbs an electric current which is independent of the voltage across it.A current source is the dual of a voltage source. The term constant-current 'sink' is sometimes used for sources fed from a negative voltage supply. Figure 1 shows the schematic symbol for an ideal current source, driving a resistor load. There are two types - an independent current source (or sink) delivers a constant current. A dependent current source delivers a current which is proportional to some other voltage or current in the circuit.