Asymmetrical Interrupting Current Rating of Medium-Voltage
... revision of the circuit breaker standards utilized the “S factor” as a multiplying factor that defined the total current a breaker was rated to interrupt at contact part. The newest revision of C37.04 replaced the S factor with the % dc as the method of evaluating the asymmetrical current offset. Th ...
... revision of the circuit breaker standards utilized the “S factor” as a multiplying factor that defined the total current a breaker was rated to interrupt at contact part. The newest revision of C37.04 replaced the S factor with the % dc as the method of evaluating the asymmetrical current offset. Th ...
NB4N507A 3.3V/5V, 50 MHz to 200 MHz PECL Clock Synthesizer
... 50% duty cycle square-wave clock output (see Figure 7). The NB4N507A can be programmed to generate a selection of input reference frequency multiples. An exact 155.52 MHz output clock can be generated from a 19.44 MHz crystal and the x8 multiplier selection. The NB4N507A is intended for low output j ...
... 50% duty cycle square-wave clock output (see Figure 7). The NB4N507A can be programmed to generate a selection of input reference frequency multiples. An exact 155.52 MHz output clock can be generated from a 19.44 MHz crystal and the x8 multiplier selection. The NB4N507A is intended for low output j ...
THS4211 THS4215
... which could permanently damage the device. See TI technical briefs SLMA002 and SLMA004 for more information about utilizing the PowerPAD thermally enhanced package. This data was taken using the JEDEC standard High-K test PCB. Power rating is determined with a junction temperature of +125°C. This is ...
... which could permanently damage the device. See TI technical briefs SLMA002 and SLMA004 for more information about utilizing the PowerPAD thermally enhanced package. This data was taken using the JEDEC standard High-K test PCB. Power rating is determined with a junction temperature of +125°C. This is ...
MAX8678 White LED Charge Pump with 1.1W Audio Amplifier General Description
... Note 1: Limits are 100% production tested at TA = +25°C. Limits over the operating temperature range are guaranteed by design. Note 2: Dropout voltage is defined as the LED_ to GND (charge pump inactive) or LED_ to NEG (charge pump active) voltage at which current into LED_ drops 10% from the value ...
... Note 1: Limits are 100% production tested at TA = +25°C. Limits over the operating temperature range are guaranteed by design. Note 2: Dropout voltage is defined as the LED_ to GND (charge pump inactive) or LED_ to NEG (charge pump active) voltage at which current into LED_ drops 10% from the value ...
On-Chip Small Capacitor Mismatches Measurement
... contains also: Section II describing the principle of the proposed capacitance to frequency conversion method based on current controlled inverters biased with betamultiplier. Section III presenting the measurement setup and respective results, as well as the comparison with previous work. Conclusio ...
... contains also: Section II describing the principle of the proposed capacitance to frequency conversion method based on current controlled inverters biased with betamultiplier. Section III presenting the measurement setup and respective results, as well as the comparison with previous work. Conclusio ...
IC-706MKII mods
... Disconnect this wire from the connector. This will enable the 2 meter band-pass filter to work outside the 2 meter band, and will restore sensitivity between about 130 MHz and about 165 MHz (above and below that range, sensitivity still stinks, especially above 165 MHz). Before this mod, a low pass ...
... Disconnect this wire from the connector. This will enable the 2 meter band-pass filter to work outside the 2 meter band, and will restore sensitivity between about 130 MHz and about 165 MHz (above and below that range, sensitivity still stinks, especially above 165 MHz). Before this mod, a low pass ...
MM74HC4046 CMOS Phase Lock Loop - Elektronik
... common signal input and a common comparator input. The signal input has a self biasing amplifier allowing signals to be either capacitively coupled to the phase comparators with a small signal or directly coupled with standard input logic levels. This device is similar to the CD4046 except that the ...
... common signal input and a common comparator input. The signal input has a self biasing amplifier allowing signals to be either capacitively coupled to the phase comparators with a small signal or directly coupled with standard input logic levels. This device is similar to the CD4046 except that the ...
Overcurrent and Overcurrent Protective Devices
... normal current flow. This is known as an “overload”. 3. Abnormal overcurrent flow with a value more than 10 times the normal current flow isFuse known as “short-circuit” or “fault” current flow. Unless otherwise noted, current (amperes) and voltage (volts) are alternating current/voltage RMS values ...
... normal current flow. This is known as an “overload”. 3. Abnormal overcurrent flow with a value more than 10 times the normal current flow isFuse known as “short-circuit” or “fault” current flow. Unless otherwise noted, current (amperes) and voltage (volts) are alternating current/voltage RMS values ...
Chopper-Fed DC Motor Drive (Discrete)
... bridge configuration, the Power Electronic device field has been set to Diodes and that the number of arms has been set to 2. Also, observe that the Measurements field has been set to Device currents, thus allowing measurement of diode currents through the Multimeter block. Now, double click on the ...
... bridge configuration, the Power Electronic device field has been set to Diodes and that the number of arms has been set to 2. Also, observe that the Measurements field has been set to Device currents, thus allowing measurement of diode currents through the Multimeter block. Now, double click on the ...
MAX2022 High-Dynamic-Range, Direct Up/ Downconversion 1500MHz to 3000MHz Quadrature Modulator/Demodulator
... Note 5: Recommended functional range, not production tested. Operation outside this range is possible, but with degraded performance of some parameters. Note 6: All limits include external component losses of components, PCB, and connectors. Note 7: It is advisable not to operate the I and Q inpu ...
... Note 5: Recommended functional range, not production tested. Operation outside this range is possible, but with degraded performance of some parameters. Note 6: All limits include external component losses of components, PCB, and connectors. Note 7: It is advisable not to operate the I and Q inpu ...
DRV632 DirectPath, 2-VRMS Audio Line Driver
... The DirectPath amplifier architecture operates from a single supply but makes use of an internal charge pump to provide a negative voltage rail. Combining the user-provided positive rail and the negative rail generated by the IC, the device operates in what is effectively a split-supply mode. The ou ...
... The DirectPath amplifier architecture operates from a single supply but makes use of an internal charge pump to provide a negative voltage rail. Combining the user-provided positive rail and the negative rail generated by the IC, the device operates in what is effectively a split-supply mode. The ou ...
