General Description Features
... (VCC = +1.5V to +3.6V, VL = +0.9V to VCC, CI/OVL ≤ 15pF, CI/OVCC ≤ 50pF, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Notes 1, 4) ...
... (VCC = +1.5V to +3.6V, VL = +0.9V to VCC, CI/OVL ≤ 15pF, CI/OVCC ≤ 50pF, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Notes 1, 4) ...
EVSTF-06-13e
... mechanically robust protections that have sufficient durability over vehicle service life such as motor housings, electronic converter cases or connectors. The isolation resistance between the high voltage bus and the electrical chassis may be demonstrated by calculation, measurement or a combinatio ...
... mechanically robust protections that have sufficient durability over vehicle service life such as motor housings, electronic converter cases or connectors. The isolation resistance between the high voltage bus and the electrical chassis may be demonstrated by calculation, measurement or a combinatio ...
IEEE Draft Guide for the Specification of Fixed
... specific application. In addition, since transmission FSC banks are typically designed to address a specific application, not every part of this guide may be applicable. The user of this guide should evaluate how and to what extent each clause applies to the development of a specification for a spec ...
... specific application. In addition, since transmission FSC banks are typically designed to address a specific application, not every part of this guide may be applicable. The user of this guide should evaluate how and to what extent each clause applies to the development of a specification for a spec ...
Summary
... Since power and ground planes are by definition a planar structure, current does not just flow through them in one direction. It tends to spread out as it travels from one point to another, in accordance with a property similar to skin effect. For this reason, inductance of planes can be described a ...
... Since power and ground planes are by definition a planar structure, current does not just flow through them in one direction. It tends to spread out as it travels from one point to another, in accordance with a property similar to skin effect. For this reason, inductance of planes can be described a ...
AN10800 Using the BLF578 in the 88 MHz to 108 MHz... Rev. 01 — 13 October 2009 Application note
... be used when mounting the BLF578 in the SOT539A package to the heatsink. Improved thermal contact is obtainable when the devices are soldered on to the heatsink. This lowers the junction temperature at high operating power and results in slightly better performance. When greasing the part down, care ...
... be used when mounting the BLF578 in the SOT539A package to the heatsink. Improved thermal contact is obtainable when the devices are soldered on to the heatsink. This lowers the junction temperature at high operating power and results in slightly better performance. When greasing the part down, care ...
Transmissive spatial light modulators with high figure-of
... As shown in Equation 3, this figure of merit is independent of cell gap thickness, and it points out the importance of LC birefringence to modulator response. Note that the FoM is indirectly wavelength and temperature dependent, because LC properties are affected by these parameters. In addition to ...
... As shown in Equation 3, this figure of merit is independent of cell gap thickness, and it points out the importance of LC birefringence to modulator response. Note that the FoM is indirectly wavelength and temperature dependent, because LC properties are affected by these parameters. In addition to ...
Stakeholder Comparison Comment Rationale Matrix 2011-09-28 AESO AUTHORITATIVE DOCUMENT PROCESS
... R1 Each legal owner of a transmission facility, legal owner of a generating unit and legal owner of an aggregated generating facility must use one of the criteria set out in requirements R1.1 through R1.13, inclusive, for each specific circuit terminal to prevent its phase protective relay settings ...
... R1 Each legal owner of a transmission facility, legal owner of a generating unit and legal owner of an aggregated generating facility must use one of the criteria set out in requirements R1.1 through R1.13, inclusive, for each specific circuit terminal to prevent its phase protective relay settings ...
List of SC A2 papers since 1968 ( docx , 46 kB )
... 12-07 Present state and trends in developing tap changers of the high speed transition resistor type with special regard to operating reliability. 12-08 On load tap changers. Important new developments for improved reliability. Increased ratings and important application problems. 12-09 Criteria for ...
... 12-07 Present state and trends in developing tap changers of the high speed transition resistor type with special regard to operating reliability. 12-08 On load tap changers. Important new developments for improved reliability. Increased ratings and important application problems. 12-09 Criteria for ...
Stakeholder Comparison Comment Rationale Matrix 2011-09-28 AESO AUTHORITATIVE DOCUMENT PROCESS
... protect the electrical network from these faults. ...
... protect the electrical network from these faults. ...
Conventional DC Machines and Universal Motor - Lab-Volt
... shall also be entitled to use parts of the copyright material as the basis for the production of his/her own training documentation for the training of his/her staff at the purchaser's site/location with acknowledgement of source and to make copies for this purpose. In the case of schools/technical ...
... shall also be entitled to use parts of the copyright material as the basis for the production of his/her own training documentation for the training of his/her staff at the purchaser's site/location with acknowledgement of source and to make copies for this purpose. In the case of schools/technical ...
AD5253 数据手册DataSheet下载
... obtain the absolute end-to-end resistance values of the RDACs for precision applications. The AD5253/AD5254 are available in TSSOP-20 packages in 1 kΩ, 10 kΩ, 50 kΩ, and 100 kΩ options. All parts are guaranteed to operate over the –40°C to +85°C extended industrial temperature range. ...
... obtain the absolute end-to-end resistance values of the RDACs for precision applications. The AD5253/AD5254 are available in TSSOP-20 packages in 1 kΩ, 10 kΩ, 50 kΩ, and 100 kΩ options. All parts are guaranteed to operate over the –40°C to +85°C extended industrial temperature range. ...
Opto-isolator
In electronics, an opto-isolator, also called an optocoupler, photocoupler, or optical isolator, is a component that transfers electrical signals between two isolated circuits by using light. Opto-isolators prevent high voltages from affecting the system receiving the signal. Commercially available opto-isolators withstand input-to-output voltages up to 10 kV and voltage transients with speeds up to 10 kV/μs.A common type of opto-isolator consists of an LED and a phototransistor in the same opaque package. Other types of source-sensor combinations include LED-photodiode, LED-LASCR, and lamp-photoresistor pairs. Usually opto-isolators transfer digital (on-off) signals, but some techniques allow them to be used with analog signals.