High-Voltage, High-Current Operational Amplifier (Rev. E)
... status. Figure 3 shows an example implementing this function. This function not only conserves power during idle periods (quiescent current drops to approximately 6mA) but also allows multiplexing in multi-channel applications. See Figure 12 for two ...
... status. Figure 3 shows an example implementing this function. This function not only conserves power during idle periods (quiescent current drops to approximately 6mA) but also allows multiplexing in multi-channel applications. See Figure 12 for two ...
SBS 1.1-COMPLIANT GAS GAUGE ENABLED
... monitors capacity change, battery impedance, open-circuit voltage, and other critical parameters of the battery pack, and reports the information to the system host controller over a serial-communication bus. It is designed to work with the bq29330 analog front-end (AFE) protection IC to maximizes f ...
... monitors capacity change, battery impedance, open-circuit voltage, and other critical parameters of the battery pack, and reports the information to the system host controller over a serial-communication bus. It is designed to work with the bq29330 analog front-end (AFE) protection IC to maximizes f ...
Datasheet - Microchip
... 11. Cycle-to-cycle jitter definition: The variation period between adjacent cycles over a random sample of adjacent cycle pairs. TJITTER_CC = Tn – Tn+1, where T is the time between rising edges of the output signal. 12. Total jitter definition: with an ideal clock input frequency of ≤ fMAX (device), ...
... 11. Cycle-to-cycle jitter definition: The variation period between adjacent cycles over a random sample of adjacent cycle pairs. TJITTER_CC = Tn – Tn+1, where T is the time between rising edges of the output signal. 12. Total jitter definition: with an ideal clock input frequency of ≤ fMAX (device), ...
MAX1558/MAX1558H Dual, 3mm x 3mm, 1.2A/Programmable-Current USB Switches with Autoreset General Description
... to determine when the short is removed to automatically restart the channel. Each channel delivers up to 1.2A and meets all IEC specifications for USB ports. Low quiescent supply current (45µA) and standby current (3µA) conserve battery power in portable applications. The MAX1558/MAX1558H safety fea ...
... to determine when the short is removed to automatically restart the channel. Each channel delivers up to 1.2A and meets all IEC specifications for USB ports. Low quiescent supply current (45µA) and standby current (3µA) conserve battery power in portable applications. The MAX1558/MAX1558H safety fea ...
PM-24-80 Power Module
... either power supply or battery charger for 24 or 48 volt d.c. systems positive, negative or floating ground. Power Modules may be employed singly or in combination, enabling the installer to scale the system output from 2500 to 10,000 watts per rack. Units may be paralleled for N + 1 redundancy and a ...
... either power supply or battery charger for 24 or 48 volt d.c. systems positive, negative or floating ground. Power Modules may be employed singly or in combination, enabling the installer to scale the system output from 2500 to 10,000 watts per rack. Units may be paralleled for N + 1 redundancy and a ...
E-IDC2B Analog Dual Input Module Installation Sheet
... Alarm latching: Configures the module for normally open dry contact initiating devices. When the NO input contact of an initiating device is closed, an alarm signal is sent to the control panel and the alarm condition is latched at the module. (Factory default) ...
... Alarm latching: Configures the module for normally open dry contact initiating devices. When the NO input contact of an initiating device is closed, an alarm signal is sent to the control panel and the alarm condition is latched at the module. (Factory default) ...
MAX5544 Low-Cost, +5V, Serial-Input, Voltage-Output, 14-Bit DAC General Description
... In unipolar mode, the output amplifier is used in a voltage-follower connection. The DAC’s output resistance is constant and is independent of input code; however, the output amplifier’s input impedance should still be as high as possible to minimize gain errors. The DAC’s output capacitance is also ...
... In unipolar mode, the output amplifier is used in a voltage-follower connection. The DAC’s output resistance is constant and is independent of input code; however, the output amplifier’s input impedance should still be as high as possible to minimize gain errors. The DAC’s output capacitance is also ...
Multiple-Choice Questions
... characteristics, and is normally located above the reactor to allow access for maintenance and testing. D. A small self-powered detector that produces Beta particle induced ionization under neutron irradiation, and is used for indication only at high power. ...
... characteristics, and is normally located above the reactor to allow access for maintenance and testing. D. A small self-powered detector that produces Beta particle induced ionization under neutron irradiation, and is used for indication only at high power. ...
IPC-7801 Reflow Oven Process Control Standard Working Draft 2
... Golden Board A reusable test vehicle with thermal characteristics similar to a production assembly, used to measure Reflow Oven performance and repeatability, and establish reflow Recipes. Sometimes called a “witness board”, “standard test vehicle”, or “reference board”. Liquidus The temperature at ...
... Golden Board A reusable test vehicle with thermal characteristics similar to a production assembly, used to measure Reflow Oven performance and repeatability, and establish reflow Recipes. Sometimes called a “witness board”, “standard test vehicle”, or “reference board”. Liquidus The temperature at ...
Control system
A control system is a device, or set of devices, that manages, commands, directs or regulates the behavior of other devices or systems. Industrial control systems are used in industrial production for controlling equipment or machines.There are two common classes of control systems, open loop control systems and closed loop control systems. In open loop control systems output is generated based on inputs. In closed loop control systems current output is taken into consideration and corrections are made based on feedback. A closed loop system is also called a feedback control system. The human body is a classic example of feedback systems.