P84662
... supply/charger used for supervision and expanded power driving capability for Fire Alarm Notification Appliance Circuits. The PS-24-8MC may be connected to any 12V or 24V (FWR or DC) Fire Alarm Control Panel (FACP) by using a Notification Appliance Circuit (NAC) or a “Dry Contact”. Primary applicati ...
... supply/charger used for supervision and expanded power driving capability for Fire Alarm Notification Appliance Circuits. The PS-24-8MC may be connected to any 12V or 24V (FWR or DC) Fire Alarm Control Panel (FACP) by using a Notification Appliance Circuit (NAC) or a “Dry Contact”. Primary applicati ...
MAX9386/MAX9387/MAX9388 Differential 5:1 or 4:1 ECL/PECL Multiplexers with Single/Dual Output Buffers General Description
... Measurements are made with the device in thermal equilibrium. Current into an I/O pin is defined as positive. Current out of an I/O pin is defined as negative. DC parameters production tested at TA = +25°C and guaranteed by design over the full operating temperature range. Single-ended data input op ...
... Measurements are made with the device in thermal equilibrium. Current into an I/O pin is defined as positive. Current out of an I/O pin is defined as negative. DC parameters production tested at TA = +25°C and guaranteed by design over the full operating temperature range. Single-ended data input op ...
A CMOS QPSK Demodulator Frontend for GPON Fei Chen
... This thesis examines the design of a QPSK demodulator frontend for GPON transceiver at end user’s side. Since lowering the cost of the terminal transceivers in an access network like GPON is a key requirement, CMOS technology is used and several areasaving design techniques are applied. The designed ...
... This thesis examines the design of a QPSK demodulator frontend for GPON transceiver at end user’s side. Since lowering the cost of the terminal transceivers in an access network like GPON is a key requirement, CMOS technology is used and several areasaving design techniques are applied. The designed ...
Document
... The following general safety precautions must be observed during all phases of operation of this instrument. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture, and intended use of the instrument. Hewlett-Packa ...
... The following general safety precautions must be observed during all phases of operation of this instrument. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture, and intended use of the instrument. Hewlett-Packa ...
Comparative study of three types of inverters based
... Figure 2.4 Output voltage waveform of single H-bridge inverter .......................................8 Figure 2.5 Output current waveform of single H-bridge inverter ........................................9 Figure 2.6 FFT Analysis of output voltage of single H-bridge inverter ..................... ...
... Figure 2.4 Output voltage waveform of single H-bridge inverter .......................................8 Figure 2.5 Output current waveform of single H-bridge inverter ........................................9 Figure 2.6 FFT Analysis of output voltage of single H-bridge inverter ..................... ...
Important notice Dear Customer, On 7 February 2017 the former
... parity. They have NAND Output Enables (nOE1, nOE2) for maximum control flexibility. The 74ALVCH162827 is designed with 30Ω series resistance in both the pull-up and pull-down output structures. This design reduces line noise in applications such as memory address drivers, clock drivers and bus recei ...
... parity. They have NAND Output Enables (nOE1, nOE2) for maximum control flexibility. The 74ALVCH162827 is designed with 30Ω series resistance in both the pull-up and pull-down output structures. This design reduces line noise in applications such as memory address drivers, clock drivers and bus recei ...
LTM4600HV - 28VIN High Efficiency DC/DC uModule
... switching DC/DC power supply. It can deliver up to 10A of DC output current with only bulk external input and output capacitors. This module provides a precisely regulated output voltage programmable via one external resistor from 0.6VDC to 5.0VDC. The input voltage range is 4.5V to 28V. A simplified ...
... switching DC/DC power supply. It can deliver up to 10A of DC output current with only bulk external input and output capacitors. This module provides a precisely regulated output voltage programmable via one external resistor from 0.6VDC to 5.0VDC. The input voltage range is 4.5V to 28V. A simplified ...
Ch28 Direct Current Circuits
... The hospital maintenance worker is right. A hospital room is full of electrical grounds, including the bed frame. If your grandmother touched the faulty knob and the bed frame at the same time, she could receive quite a jolt, as there would be a potential difference of 120 V across her. If the 120 V ...
... The hospital maintenance worker is right. A hospital room is full of electrical grounds, including the bed frame. If your grandmother touched the faulty knob and the bed frame at the same time, she could receive quite a jolt, as there would be a potential difference of 120 V across her. If the 120 V ...
DT9829 Series User’s Manual Title Page UM-25325-A
... EN61000-6-1 requirements and also with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, an ...
... EN61000-6-1 requirements and also with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, an ...
STM1810
... When VCC falls below 1 V, the RST output no longer sinks current, but becomes an open circuit. In most systems this is not a problem, as most MCUs do not operate below 1 V. However, in applications where RST output must be valid down to 0 V, a pull-down resistor may be added to hold the RST output l ...
... When VCC falls below 1 V, the RST output no longer sinks current, but becomes an open circuit. In most systems this is not a problem, as most MCUs do not operate below 1 V. However, in applications where RST output must be valid down to 0 V, a pull-down resistor may be added to hold the RST output l ...
TPS65982 USB Type-C and USB PD Controller, Power Switch and
... SPI serial master input from slave. This pin is used during boot sequence to determine if the flash memory is valid. Refer to the Boot Code section for more details. Ground pin when unused. ...
... SPI serial master input from slave. This pin is used during boot sequence to determine if the flash memory is valid. Refer to the Boot Code section for more details. Ground pin when unused. ...
the zero-pole transformation noise reduction technique for
... sensor and photo-detector systems. Charge amplifiers are used in the front-end design of systems that have an input signal in the form of charge or a current pulse. Applications for such systems include photography, radar imaging, medical imaging, X-ray fluorescence applications and particle-physics ...
... sensor and photo-detector systems. Charge amplifiers are used in the front-end design of systems that have an input signal in the form of charge or a current pulse. Applications for such systems include photography, radar imaging, medical imaging, X-ray fluorescence applications and particle-physics ...
