HMC-C058
... field replaceable SMA connectors. Covering DC to 18 GHz, the switch offers high isolation and low insertion loss. The switch features >65 dB isolation up to 6 GHz and >50 dB isolation up to 18 GHz. A CMOS interface allows a single +5V bias voltage at very low DC currents. ...
... field replaceable SMA connectors. Covering DC to 18 GHz, the switch offers high isolation and low insertion loss. The switch features >65 dB isolation up to 6 GHz and >50 dB isolation up to 18 GHz. A CMOS interface allows a single +5V bias voltage at very low DC currents. ...
LTC6990 - TimerBlox: Voltage Controlled Silicon Oscillator
... amount of current sourced from the SET pin (ISET) programs the master oscillator frequency. The ISET current range is 1.25µA to 40µA. The output oscillation will stop if ISET drops below approximately 500nA. A resistor connected between SET and GND is the most accurate way to set the frequency. For ...
... amount of current sourced from the SET pin (ISET) programs the master oscillator frequency. The ISET current range is 1.25µA to 40µA. The output oscillation will stop if ISET drops below approximately 500nA. A resistor connected between SET and GND is the most accurate way to set the frequency. For ...
GCP 557 T8 LED FAQ
... the like FTL T8 only as the basic principle of working is that this is made of passive components and its impedance is matched to 32W T8 FTL. ...
... the like FTL T8 only as the basic principle of working is that this is made of passive components and its impedance is matched to 32W T8 FTL. ...
HMC349MS8G - SeekDataSheet
... switch in a low cost 8 lead MSOP8G surface mount package with an exposed ground paddle. The switch is ideal for cellular/PCS/3G basestation applications yielding 50 to 60 dB isolation, low 0.8 dB insertion loss and +52 dBm input IP3. Power handling is excellent up through the 3.5 GHz WLL band with t ...
... switch in a low cost 8 lead MSOP8G surface mount package with an exposed ground paddle. The switch is ideal for cellular/PCS/3G basestation applications yielding 50 to 60 dB isolation, low 0.8 dB insertion loss and +52 dBm input IP3. Power handling is excellent up through the 3.5 GHz WLL band with t ...
Analog Devices Welcomes Hittite Microwave Corporation
... Covering 0.7 to 3.8 GHz, the insertion loss is typically less than 2.5 dB. The attenuator bit values are 1 (LSB), 2, 4, 8, and 16 dB for a total attenuation of 31 dB. Accuracy is excellent at ±0.2 dB typical with an IIP3 of up to +48 dBm. Five bit control voltage inputs, toggled between 0 and +3 to ...
... Covering 0.7 to 3.8 GHz, the insertion loss is typically less than 2.5 dB. The attenuator bit values are 1 (LSB), 2, 4, 8, and 16 dB for a total attenuation of 31 dB. Accuracy is excellent at ±0.2 dB typical with an IIP3 of up to +48 dBm. Five bit control voltage inputs, toggled between 0 and +3 to ...
Physics
... Second harmonic of this source = 492Hz or 508 Hz Which gives 5 beats per second, when sounded with a source of frequency 513 Hz. Therefore unknown frequency = 254 Hz 128. A coil is self-inductance L is connected in series with a bulb B and an AC source. Brightness of the bulb decreases when : (1) an ...
... Second harmonic of this source = 492Hz or 508 Hz Which gives 5 beats per second, when sounded with a source of frequency 513 Hz. Therefore unknown frequency = 254 Hz 128. A coil is self-inductance L is connected in series with a bulb B and an AC source. Brightness of the bulb decreases when : (1) an ...
Cavity magnetron
The cavity magnetron is a high-powered vacuum tube that generates microwaves using the interaction of a stream of electrons with a magnetic field while moving past a series of open metal cavities (cavity resonators). Bunches of electrons passing by the openings to the cavities excite radio wave oscillations in the cavity, much as a guitar's strings excite sound in its sound box. The frequency of the microwaves produced, the resonant frequency, is determined by the cavities' physical dimensions. Unlike other microwave tubes, such as the klystron and traveling-wave tube (TWT), the magnetron cannot function as an amplifier, increasing the power of an applied microwave signal, it serves solely as an oscillator, generating a microwave signal from direct current power supplied to the tube.The first form of magnetron tube, the split-anode magnetron, was invented by Albert Hull in 1920, but it wasn't capable of high frequencies and was little used. Similar devices were experimented with by many teams through the 1920s and 30s. On November 27, 1935, Hans Erich Hollmann applied for a patent for the first multiple cavities magnetron, which he received on July 12, 1938, but the more stable klystron was preferred for most German radars during World War II. The cavity magnetron tube was later improved by John Randall and Harry Boot in 1940 at the University of Birmingham, England. The high power of pulses from their device made centimeter-band radar practical for the Allies of World War II, with shorter wavelength radars allowing detection of smaller objects from smaller antennas. The compact cavity magnetron tube drastically reduced the size of radar sets so that they could be installed in anti-submarine aircraft and escort ships.In the post-war era the magnetron became less widely used in the radar role. This was because the magnetron's output changes from pulse to pulse, both in frequency and phase. This makes the signal unsuitable for pulse-to-pulse comparisons, which is widely used for detecting and removing ""clutter"" from the radar display. The magnetron remains in use in some radars, but has become much more common as a low-cost microwave source for microwave ovens. In this form, approximately one billion magnetrons are in use today.