J322X Replacement Seismic Telemetry System Rev B 08/2014 VLF
... that frequency drift is no longer a problem. The VCO utilizes a plug in daughter board so that any power supply/amplifier card can be used with any VCO card without the need for recalibration of the VCO. VCO over modulation has been completely eliminated by the use of rail to rail opamps in the prea ...
... that frequency drift is no longer a problem. The VCO utilizes a plug in daughter board so that any power supply/amplifier card can be used with any VCO card without the need for recalibration of the VCO. VCO over modulation has been completely eliminated by the use of rail to rail opamps in the prea ...
Experiment 27: AC Circuits: LR, LCR
... b) Upon your instructor’s approval, turn ON the power, and adjust the output voltage to between 9.80 and 9.95 volts (or to YOUR maximum voltage if you can’t reach 9.80 V). Record this as VOUT to the accuracy of 0.05 V. c) Measure and record the voltages VL across the coil and and VR across the resis ...
... b) Upon your instructor’s approval, turn ON the power, and adjust the output voltage to between 9.80 and 9.95 volts (or to YOUR maximum voltage if you can’t reach 9.80 V). Record this as VOUT to the accuracy of 0.05 V. c) Measure and record the voltages VL across the coil and and VR across the resis ...
ITtestPapers.com
... ITtestPapers.com – Placement Papers, Interview Questions and Tutorials ------------------------------------------------------------------------------------------------------------------------------7. There was a circuit consisting of AC voltage source and one inductance. Inductance value=0.2mH AC v ...
... ITtestPapers.com – Placement Papers, Interview Questions and Tutorials ------------------------------------------------------------------------------------------------------------------------------7. There was a circuit consisting of AC voltage source and one inductance. Inductance value=0.2mH AC v ...
Fluke 752A Reference Divider Specifications
... 10:1 and 100:1 with output uncertainties of less than 0.2 ppm and 0.5 ppm respectively. Before each use, the Fluke 752A is easily calibrated with only a stable source and a null detector. The entire procedure takes only five minutes and does not require external standards. ...
... 10:1 and 100:1 with output uncertainties of less than 0.2 ppm and 0.5 ppm respectively. Before each use, the Fluke 752A is easily calibrated with only a stable source and a null detector. The entire procedure takes only five minutes and does not require external standards. ...
LT1969 - Dual 700MHz, 200mA, Adjustable Current Operational Amplifier
... The LT®1969 is an adjustable current version of the popular LT1886, a 200mA minimum output current, dual op amp with outstanding distortion performance. The adjustable current feature is highly desirable in applications where minimum power dissipation is required while still being able to provide ad ...
... The LT®1969 is an adjustable current version of the popular LT1886, a 200mA minimum output current, dual op amp with outstanding distortion performance. The adjustable current feature is highly desirable in applications where minimum power dissipation is required while still being able to provide ad ...
TEXAS INSTRUMENTS (DRV134PA) AUDIO LINE DRIVER
... output signals under loaded conditions. To measure SBR an input signal is applied and the outputs are summed as shown in Figure 5. VOUT should be zero since each output ideally is exactly equal and opposite. However, an error signal results from any imbalance in the outputs. This error is quantified ...
... output signals under loaded conditions. To measure SBR an input signal is applied and the outputs are summed as shown in Figure 5. VOUT should be zero since each output ideally is exactly equal and opposite. However, an error signal results from any imbalance in the outputs. This error is quantified ...
OPAx322-Q1 20-MHz, Low-Noise, 1.8-V, RRI/O
... Control-Loop Amplifiers Communications Security Scanners ...
... Control-Loop Amplifiers Communications Security Scanners ...
AD7845 数据手册DataSheet 下载
... VOUT = – D × VREF where D is the fractional representation of the digital word. (D can be set from 0 to 4095/4096.) The amplifier can maintain ± 10 V across a 2 kΩ load. It is internally compensated and settles to 0.01% FSR (1/2 LSB) in less than 5 µs. The input offset voltage is laser trimmed at wa ...
... VOUT = – D × VREF where D is the fractional representation of the digital word. (D can be set from 0 to 4095/4096.) The amplifier can maintain ± 10 V across a 2 kΩ load. It is internally compensated and settles to 0.01% FSR (1/2 LSB) in less than 5 µs. The input offset voltage is laser trimmed at wa ...
TRANSPAK T700-0001 ™ Loop Powered Isolator
... input (typically 4-20mA). It takes its power source voltage and the output current loop drive (500 Ohm, 10V compliance, max.) from the input current loop. The 1-20mA output current follows the input current signal. Span adjustment is provided to adjust for load variations. There are two (+) output t ...
... input (typically 4-20mA). It takes its power source voltage and the output current loop drive (500 Ohm, 10V compliance, max.) from the input current loop. The 1-20mA output current follows the input current signal. Span adjustment is provided to adjust for load variations. There are two (+) output t ...
AD8041
... Output Voltage Swing: RL = 10 kΩ Output Voltage Swing: RL = 1 kΩ Output Voltage Swing: RL = 50 Ω ...
... Output Voltage Swing: RL = 10 kΩ Output Voltage Swing: RL = 1 kΩ Output Voltage Swing: RL = 50 Ω ...
Communication and Sensing Circuits on Cellulose
... high input impedance of the patch to the 50 Ω level of the feeding microstrip. After verification, the single patch has been used as radiating element in a 2 × 2 patch array antenna, see Figure 4b. The purpose of the array is to have a broadside radiation and to improve the gain with respect to that ...
... high input impedance of the patch to the 50 Ω level of the feeding microstrip. After verification, the single patch has been used as radiating element in a 2 × 2 patch array antenna, see Figure 4b. The purpose of the array is to have a broadside radiation and to improve the gain with respect to that ...
This work shows the possibility of using a low-cost 130
... HE recent explosion of high-data rate fixed and mobile wireless communications has put into focus the future need for low-cost and miniature fully integrated systems that enable the transfer of gigabits-per-second data reliably over a certain distance [1]. The exploitation of mm-wave frequencies for ...
... HE recent explosion of high-data rate fixed and mobile wireless communications has put into focus the future need for low-cost and miniature fully integrated systems that enable the transfer of gigabits-per-second data reliably over a certain distance [1]. The exploitation of mm-wave frequencies for ...
